

KDE because I liked it when I used it and wanted it to get even better. And Lichess because it’s what I wish all free services were like. I should do more.


KDE because I liked it when I used it and wanted it to get even better. And Lichess because it’s what I wish all free services were like. I should do more.
The Music of the Ainur is a pathway to many abilities which some deem to be… unnatural.


Absolutely. When you’re making a book cover, a pretty typical method is to take book board (chipboard-like material, similar to the back cover of notebooks) and glue it on book cloth or paper. Then you fold over edges of the cloth/paper. You don’t need to cover the inside because that’s where the actual pages of the book will be, but you need some overlap (e.g. 25mm).
But the corner is a bit tricky. If you don’t trim at all, you have an extra triangle of folded paper that gets in the way. If you cut it off too close to the book board, you will see the board peeking through. So you want to cut the corner off with a little gap. And if you get the angle wrong, the fold doesn’t look quite right. This jig gives both spacing and angle, and it has an added bonus of the notches to let you mark your cuts for the fold over on each side.
The first 30 seconds of this video illustrate it pretty well: https://www.youtube.com/watch?v=N4IzpDqbHqU


I really like Build123d. I hope someday the model sites like Printables and Makerworld support it like they do OpenSCAD.


Karl Urban is also great


Nice, I’ll take a look. How is the mobile experience?


Yeah, no problem.
This is my first attempt at posting a comment with pictures, but hopefully these show up:




Yes. When I tried it, it was not very stable and the shortcuts didn’t really work on mobile. But I know a lot has changed, so I’ve been meaning to go back and give it another shot.


Backlinking is when you link to a page, it links back.
For example, if I have a daily journal, I can say Fixed a problem with my [[Raspberry Pi]] setup... and then a few weeks later I can say Found a new use for [[Raspberry Pi]]..., etc.
Now when I go to the Raspberry Pi page, it shows me a list of times I’ve linked to the page and the context.
I use this all the time with Logseq, but I find Logseq pretty unpolished, infrequently updated, etc., so I’m always on the lookout for something nicer.


I’m getting a Cloudflare error trying to access your demo site.
Also, do you support back linking? That’s a feature that’s very important to me.
I finally got around to setting up my internal services with TLS. It was surprisingly easy with a Caddy docker image supporting Cloudflare DNS challenge.
I did this because various services I use are starting to require https.
Now everything is on a custom domain, https, and I can access it through Tailscale as usual.


Azure is not Entra. AAD became Entra. They did it because AAD was becoming less about Azure and covering more things than directories. So a rebranding made sense.
It’s a pretty dumb name, though. It doesn’t really mean much when you hear it, and it sounds too similar to other common words.
For the plant, it drops the seed again when you trample it, so it won’t hurt your run.
Maybe unpopular opinion here, but I just read The Three Musketeers, and it’s not even close to The Count of Monte Cristo.
The characters wildly change in tone and basic morals, the heroes are dirtbags, and the plot wanders.
I still enjoyed it, but it just wasn’t the same.


Largely agree, with a couple exceptions: Undiscovered Country and First Contact are good; Into Darkness is bad.


There’s a chain near me that makes a breakfast sandwich with eggs, bacon, white cheddar, a really excellent garlic aioli, and Ciabatta bread.
I go there way too much.


This might be my biggest TNG complaint. The character and the actor are good (or at least decent if we’re being picky), but almost every time the focus is on her, the writing is absolutely awful.
Fringe is great. Season 1 is a bit “Monster of the week” but when it gets going it’s a great ride.
I’ve been looking into this as well and just bought my first components.
I’m trying Meshtastic first and then will try Meshcore.
What does everybody think of Reticulum Network and RNode? It honestly seems superior conceptually to Meshtastic/Meshcore, but I’m not sure how good it is in practice or if anybody is actually using it.